Related Products
PRODUCT DESCRIPTION
Nazgul5 HD is a 5" size BNF (Bind-and-Fly)
quadcopter with Caddx Vista Digital HD System on it. We sticked the lighter
Caddx Vista on one of our new updated XL5 V5 FPV frames. Pre-tuned and setup,
everything you need is just bind-and-fly! Loads of power and smooth flights
guaranteed using our popular XING-E motors with long-lasting NSK bearings. Got
a hard hit and snapped an arm? Don't worry, get some spares with your order and
easy-swap out in field. Wanna strap your GoPro on that beast as well? Checkout
our collection of high quality TPU prints for your cam!
HIGHLIGHTS:
- 5mm arm design for more durability
- Easy-Swap arms
- LED illuminated Logo
- XING-E 2207 motors and NAZGUL 5140 props
- 5" version also fits 5.1" style propellers
- Popular True-X configuration
- TPU crash-guards
- Fits both 30.5x and 20x stacks
Nazgul5(XL5 V5) frame specs:
SucceX-E F7 45A flight stack
XING-E 2207 FPV Motor (6S 1800kv / 4S 2750kv)
Wheelbase:
240mm*240mm
Body size: 170*170mm
Propeller size: 5 inch /5.1 inch
FC pattern: 30.5*30.5/20*20 mm
FPV cam spacing: 19mm
Weight: 400.8g (without battery)
PRE-TUNED & PRE-SETUP:
- Don't worry about tuning, we did that for you already!
A basic PID- and Filter tuning was applied for a great flight experience!
To restore lost tunes or updates, please check our linked
article on "Firmware/Factory Dumps"
- Angle-Mode (self balancing level mode) is enabled by
default to make sure your first flight doesn't end in a mess!
Please check our linked article on "How to disable
Angle-Mode, activate Acro-Mode"
Nazgul5 HD Quad BNF Included Components and Parts
Prebuilt and tested Quadcopter
1x Nazgul5(XL5 V5) Frame
1x Caddx Polar Vista Digital HD System Kit
1x Albatross LHCP RP-SMA 5.8g antenna
2sets x Nazgul 5 inch 3-blades (Set of 4 - Color may
vary)
1x 20*200mm Microfiber PU Leather Battery Strap (Color
May Vary)
1x 20*250mm Microfiber PU Leather Battery Strap (Color
May Vary)
FC // SucceX-E F7 Flight controller
- MCU: STM32F22RET6 216MHz
- Gyro: 20689
- Baro: DSP310 (Barometer can only be used with
Betaflight 4.3.0 and above)
- OSD: IFLIGHT OSD (AT7456E)
- BEC: 5V 2.5A
- BlackBox: 16MB
- Uart: 4*UART(UART1、UART2、UART4、UART5)
- UART1 for VTX HD(for 4-6S Vista,for 4S DJI Air Unit)/AnalogTelemetry
- UART2 for Receiver
- UART4 for Free
- UART5 for ESC Telemetry
- 4×Dshot/PWM outputs
- Smartaudio & IRC Tramp VTX protocol supported
- WS2812 led Strip: Yes
- Bepper: Yes
- Firmware: IFLIGHT_SUCCEX_E_F7
- Outer Size: 36*36mm / 30.5*30.5/φ4 mounting
- Weight: 6.9g
ESC // SucceX-E 45A 2-6S BLHeli_S 4-in-1 ESC
- Dimension: 40*43mm
- Mounting Holes: 30.5*30.5mm/Φ3mm
- Weight: 14.4g
- Supports 2-6S Lipo input
- STM32F051 MCU, 48Mhz Runs BLHELI 16.X Firmware
- Current sensor: YES
- BEC: NO
- Supports: DShot150/300/600/1200/MultiShot/OneShot etc.
- Target: G-H-30 BLS 16.7
Changelog:
June 2021: Upgraded SucceX-E F4 flight controller to
SucceX-E F7
Additional Suggested Parts
DJI HD FPV Goggles
Radio Controller
Battery 4S 1550mAh
Battery 6S 1300mAh
GoPro Mounts
Important
The DJI Remote Controller is recommended for beginners
since you won't need to set up another receiver, but it is also optional in
this BNF drone because it is NOT required in order to use the FPV system. If
you don't choose to use the DJI Remote Controller, you can choose a receiver
option for your transmitter. and then bind to your own radio as usual.
Our current frsky receivers default version in 2.XX,
requires to use the same version of frsky transmitter.
If you have none frsky transmitter, please downgrade the
version lower than 2.X.X, www.frsky-rc.com for more details.